My Blog List

Akai AC Error Codes and Troubleshooting Method


Akai AC Error Codes and Troubleshooting Method

This air conditioner is equipped with a self-diagnosis function to help you identify potential problems. Should you encounter problems with your air conditioner, contact our after sales support centre using the details on the bottom of the page.However, before calling for service, consult the selfdiagnosis information below.
Error Code
Meaning
dF
Indicates “dF”or heating icon blinks. Defrost indication. Blinks once per second
E2
Room temperature sensor fault. Blinks once every 8 seconds.
E3
Coil temperature sensor. Blinks twice every 8 seconds.
E8
Indoor fan fault. Blinks 3 times every 8 seconds.
E5
Outdoor feedback. Blinks 6 times every 8 seconds.
E7
External feedback fault. Blinks 7 times every 8 seconds.
E0
Open the door fault. Open the door fault. Blinks 3 times every 8 seconds.
E1
Outdoor tube temperature sensor faults. Blinks 4 times every 8 seconds.
E6
(EEPROM) Communication failures. Blinks 6 times every 8 seconds.
FF
Outdoor temperature exceeds scope (too cold). Blinks once per second.

Akai AC Error Codes And TroubleShooting Method

When You Face  Any Error Code In Akai Ac You Must Read this Complete  Article In This Article We Wrote Complete Akai AC Error Codes And Trouble Shooting Methods.
Problems: Error code “E1” in LED window
Causes: When This Error Is Coming Environment temperature sensor is broken.
Suggest Solutions: After This Happens Replace the temperature sensor
Problems: Error code “E2” in LED window
Causes: When “E2” Is Coming Temperature sensor on the evaporator is broken
Suggest Solutions:When You Face “E2” Error Then Replace the sensor
Problems: Error code “E3” in LED window
Causes: This Error Means Cooling system malfunction caused by the lack of refrigerant
Suggest Solutions: After Face This Error Contact the local repairing technician directly
Problems: Error code “E4” in LED window the red FULL light is bright
Causes: When Your Portable Ac Water tray is full in the heating mode, but the unit is still working.
Suggest Solutions: After That Empty water in water plate.
Problem: When You Face This Error Your Air conditioner does not work.

Possible cause and solution:

  1. After Face This Problem A Lot Of Problems You Face .
  2. Power failure/disconnected/loose connections; check the power supply and ensure the unit is properly connected.
  3. When You See Timer-on function is activated; cancel it.
  4. Damaged indoor/outdoor unit fan motor; call the after sales support line to arrange a service.
  5. Faulty compressor/thermomagnetic circuit breaker; If Not Clear Then You Must call for service.
  6. Faulty protective device or fuse; call for service.
  7. Voltage is higher or lower than the required range; call for service.
  8. Electronic control board is damaged;And You Must call for service When You Face This Problem.
Problem: Remote control is unresponsive
Possible cause and solution:
  1. After That Remote control is too far away; move closer to the indoor unit
  2. Remote control batteries are flat; replace.
  3. Path to the signal receiver is blocked; remove obstructions
Problem: Cooling (Heating) efficiency is not good
Possible cause and solution:
  1. Unsuitable temperature setting — adjust fan speed.
  2. Blocked air intakes/ outlets — clear obstructions.
  3. Dirty air filter — clean the filter.
  4. After This Happens Fan speed is set to LOW — increase.
  5. Other sources of heat in the room — check
Problem: Indoor unit does not work straight after restarting it
Possible cause and solution: This is not a fault. Once the air conditioner is stopped, you will have to wait for approximately 3 minutes before the unit can be restarted
Problem: Strange odour coming from the outlet
Possible cause and solution:
  1. Odour in the room (from building material, furniture or smoke) is recirculated
  2. When You See Dirty air filter — clean the filter

Problem: Noise like running water when cooling

Possible cause and solution: After That Refrigerant is flowing inside the unit — no cause for concern
Problem: Mist is emitted when cooling
Possible cause and solution: Cold air used for rapid cooling of the air in the room may resemble fog — no cause for concern
Problem: Mist is emitted when heating
Possible cause and solution: Moisture from the defrosting process generates mist — no cause for concern.
Problem: Low noise is emitted during operation.
Possible cause and solution:
  1. A low hissing sound is caused by the refrigerant flowing.
  2. A low squeak sound is caused by the plastic parts expanding and contracting due to temperature fluctuations.

Problems with Wi-Fi connectivity

Problem: App does not show the air conditioner.
Possible cause and solution:
  1. If You Face This Problem Check and ensure you have Wi-Fi enabled on your smartphone.
  2. When This Happens Check and ensure your smartphone and the air conditioner are connected to the same wireless router.
  3. If the air conditioner is correctly connected to the wireless router, Then the Wi-Fi indicator light on the display should be on
Problem: Remote control via smartphone does not work, despite correct connection
Possible cause and solution: When You See It’s Does Not Working Then Restart your AKAI Home App or reconnect your smartphone with the wireless router



voltas AC unlock passwords